Tips You Need To Know About Split Air Conditioner Maintenance

23/10/2018 by 4 Comments

Tips You Need To Know About Split Air Conditioner Maintenance

Do you have a split AC at home? If yes, it’s time you start appreciating it more. Air conditioner adds on to the comfort of your home and gives you more control over the temperature.

While your HVAC system is a boon for your home, it most definitely does require a good amount of servicing too.

The best way to increase the shelf life of your split AC is by getting it regularly serviced. There are several professional air conditioning services in Jacksonville, FL that you can avail. [Read more…]

Filed Under: HVAC Tagged With: , , , , , , , , , ,

How To Replace Bearing For Electric Motor?

09/08/2016 by Leave a Comment

With advance technology,we can found the root cause for abnormal sound using Vibration Analysis for rotating equipment.When vibration owner confirm that bearing are defected,we must plan to change or replace a bearing.This time I would like to share video completed method how to replace electric motor bearing.

This is common activities for Electrician to perform bearing replacement during daily routine or turnaround / shutdown.We must ensure all bearing condition for our electrical motor in good performance to prolong bearing life time and can avoid unplanned downtime that can increase maintenance cost. Read More

Filed Under: Electric Motor Tagged With: , , , , , , , , , , , , , , ,

How To Use Bearing Induction Heater ?

01/08/2016 by Leave a Comment

This post I would like to share a video How To Use Bearing Induction Heater.Normally when we dealing with bigger motor or pump bearing,it’s quite difficult to install bearing into shaft because a tolerance gap is small.If we use a bearing pusher to install bigger size bearing into shaft,it’s risky and probably percentage of bearing was damage is high.That why we must use bearing induction heater for more safe and easy bearing installation.

In this video, I used old version of SKF bearing induction heater but still working perfectly without any problem.For latest version and model of Induction Heater from SKF,please visit SKF website  Read More

Filed Under: Do It Your Self Tagged With: , , , , , , , , , , , , , , , , , ,

Completed Guideline How To Verify,Setup And Installation for ENDRESS+HAUSER Ultrasonic Clamp-On Flow Meter

28/07/2016 by Leave a Comment

This post,I would like to share video from ENDRESS+HAUSER about completed guideline how to install Ultrasonic Clamp-On Flow Meter Proline Prosonic start from determine right position to install a sensors,mounting specs and measurement,how to setup and install sensor,cable route and how to do cable termination from transmitter to sensor.

From this video,I hope all of you can get the clear view,how to setup,install and commissioning your Ultrasonic Clamp-On Flow Meter with perfect and right method to ensure this unit working properly without any trouble.ENDRESS+HAUSER always improved their customer service and technical support from time to time to ensure their products can meet customer satisfaction. Read More

Filed Under: Instruments Tagged With: , , , , , , , , , , , , , , , , ,

How To Setup and Programming Endress+Hauser PROSONIC Clamp-On Ultrasonic Flow Meter

27/07/2016 by Leave a Comment

Do you familiar with ENDRESS+HAUSER brand?This time I would like to share about How to setup and programming the PROSONIC Clamp-On Ultrasonic Flow Meter.Also I have attached with video from ENDRESS+HAUSER,method and detail step how to setup the program for PROSONIC Clamp-On Ultrasonic Flow Meter.It very user friendly and easy to setup.

This is basic information about Endress+Hauser Prosonic Clamp-On Ultrasonic Flow Meter :-

The measuring device described in these Operating Instructions is to be used only for measuring the flow rate of liquids in closed pipes.
Examples:
• Acids, alkalis, paints, oils
• Liquid gas
• Ultrapure water with low conductivity, water, wastewater  Read More

Filed Under: Instruments Tagged With: , , , , , , , , , , , , , , , , , ,

Selecting a suitable generator for your application- Part 2

05/12/2014 by 3 Comments

Last time,on my post “Selecting a suitable generator for your application – PART 1”,I’m promised to continue discussion about selecting a suitable generator for your application.In this post, I explained details and shared some tips to get a suitable generator for your application.

What’s this THD?

For ensuring smooth and continuous running of generator it is important to measure its THD –total harmonic distortion. When a significant portion of the load on a generator (or any power source for that matter) is non-linear, all the loads fed by the source will see this distortion. read more

Filed Under: Generator Tagged With: , , , , , ,

Selecting a suitable generator for your application- Part 1

04/12/2014 by 4 Comments

Ever tried to buy a generator? No? Then, you are saved a potential existential crisis, by God’s grace!! Ask someone who has tried to buy and actually landed with one.

And, he or she would tell you about the trials and tribulations involved in the process. It’s like trying to decode the proverbial riddle: horse before the cart or the cart before the horse!

Do you need a standby generator, single-phase, three-phase, kW, KVA, welder, or motor starting generators? Or, do you need a diesel run or a petrol run generator? read more

Filed Under: Generator Tagged With: , , , , , ,
Next Page »