X

Automatic voltage regulator for generator

The AVR ( automatic voltage regulator ) is suitable for supplying power to the fields of either brushless or commutator type exciters and will maintain the A.C generator voltage within plus and minus 1% of the preset value with paralleling.

When the load varies between no load and rated load and with a frequency changes more than plus minus 4%.Upon application or rejection of rated load,the generator voltage recovers to plus and minus 1% within 0.3 second on most AVR exciter in A.C generator combination.

The AVR is suitable for operation in ambient temperature up to 50 ‘c and will deliver a power output of 150 watts with a max. current of 3 A.Under some circumstances the A.C generator wave shape changes considerably from no load to rated load.

It is due to the type of load,hence the r.m.s average or peak voltage does not stay in proportion.In this situation,i.e : greater than 10% harmonic distortion,the voltage regulation may be outside the limit quoted.

 How the Auto voltage regulator (AVR) operate?

When rated load is switched on to A.C generator the voltage fall,typically to approximately 70% of its no load value.If the A.C generator voltage is to be maintained near to its no load value,then its excitation must be increased progressively in proportion to the amount of load or more correctly in proportion to the fall in voltage.The AVR perform this task.

The voltage to be regulated is derived from the line UR and VR of the A.C generator and is potentially divided by the resistance chain R1,R2 and R3.The signal appearing between terminals T2 of potentiometer RV1 and the junction of C1 and R3.

Rectifier diodes D1 and D2 rectify the signal voltage.An error signal is produced by the difference between the signal voltage and a stabilized reference voltage developed across the zener diodes D9 and D10.Capacitor C1 smoothed the signal.This error signal is applied to the base emitter circuit of VT1.The A.C generator voltage is adjusted by the potentiometer RV1.

For more detail about AVR diagram and operation,please refer to my post : Basic of AVR and operation

Lemau: Lemau is Owner of Electricneutron.com .Involved in Electrical & Automation Engineering since 2001. Passionate to shared all experience & knowledge about Electrical.

View Comments (31)

  • Topic is very beautiful and important information in it, God bless you from all harm, thank you very much

  • In my plant having 43 Mw BHEL generator and bhel AVR also in that having two modes. PF regulation and MVAR regulation if we r maintaining the grid side reactive power our power factor also vl maintain properly for smooth operation. In MVAR regulation giving one pulse the response variation is normal but kept in PF regulation the response variation is more so which regulation is best what is the different between these two regulations plz explain this

  • Hmm, do you have any pictures or diagrams that can explain the operating principle of AVR in generator? thank you for sharing it to us..

  • I need to test the AVR of International Electric Co. Type GX300PR.I need help, anyone still a copy of operation manual for this AVR.
    Thank you

  • ajmal khan

    it is useful information about avr but i need fully curcuits and manual.which is helpful me.

  • DEAR SIRS

    WE ARE LEADING SUGAR MANUFACTURER IN INDIA. WE REQUIRE FOLLOWING ITEM FOR OUR GENERATOR. DETAILS OF WHICH ARE GIVEN AS UNDER. KINDLY MAIL US OFFER FOR THIS ITEM THROUGH YOUR AUTHORIZED DEALERS OR SLEF.

    1 ELECTRONIC CONTROLLER CARD PC191 FOR 3 MW ALTERNATOR AVR 415 VOLT, 3 PHASE AC, 50 HZ BHEL MAKE

    • we have wide range of avr.we have 1 mw to 50 mw and more. we have stock of 3 mw alternator avr 415 volts, 3 phase ac 50 hz.

  • I absolutely love your blog and find many off your post's to be exactly I'm looking for.

    Does one offer guest writers to write content for you
    personally? I wouldn't miknd composing a post or
    elaborating on a few of the subjects you write in relation to here.
    Again, awezome web site!

  • Dear sir,
    One of our power house is having Blakstone 11Kva 4 Generators. The type of the AVR has fixed in BRUSH which is now Obsolete in the company. EXE voltage is 240 and EXE amp is 34.5 A. i tried to repair the AVRs and spare parts also obsolete. what can i do. do you know any AVR model which we can fix with synchronous facility.

  • Excellent blog you have here but I was curious about if you recognized of any
    message boards that include the same topics talked about in this
    article? I'd really like to be a part of online community
    wherein I can get comments from other knowledgeable individuals that promote the same interest.
    If you have any recommendations, remember to inform me.
    Thanks a lot!